SUPREMACYIN LEAK DETECTION
Book now
Where pools leak

Skimmer leaks: the most common pool leak

If your pool keeps dropping to the same spot partway down the skimmer opening, the skimmer is a prime suspect. It is one of the leaks we find most often.

By the Supremacy in Leak Detection teamUpdated 3 min read

New skimmer set in a fresh concrete patch in the pool deck
On this page
  1. Why skimmers leak
  2. Signs
  3. How we find it
  4. Why North Texas is hard on skimmers
  5. A quick check you can do
  6. When a patch will not hold
  7. Skimmer lines
  8. Repair options

Why skimmers leak

A skimmer is a plastic box set into the concrete at the edge of the pool. The pool shell and the deck move a little with heat, cold and soil. The skimmer does not move the same way, so the joint between them takes the strain. Over time it cracks. The skimmer body itself can crack too, especially after a hard freeze.

Signs

  • The water stops dropping partway down the skimmer opening.
  • A gap or crack where the skimmer meets the pool, under the tile.
  • Cracked or sunken deck around the skimmer lid.
  • Wet soil near the skimmer on a dry day.
A new skimmer being set into the deck during a skimmer replacement
A new skimmer going in. The old one was cracked at the throat.

How we find it

We release dye at the skimmer throat in still water and watch. We also pressure test the skimmer line, because the pipe under it can leak too, and it is often the cause rather than the box.

Why North Texas is hard on skimmers

The skimmer sits right at the edge of the pool, half in the deck and half in the shell. When the clay under the deck swells in wet months and shrinks in droughts, the deck moves and the shell does not, or not the same way. The skimmer gets pulled between them. Add summer heat on the lid and freezes in winter, and the joint at the skimmer throat is often the first seam to open.

A quick check you can do

Turn the pump off and let the water go still. Squeeze a few drops of pool dye or food coloring near the seam where the skimmer meets the pool wall, under the water line. If the color gets pulled into a crack, you have found one leak. Write it down, and still have the lines tested: a skimmer leak and a line leak often show up together.

When a patch will not hold

A small separation at the throat can often be sealed with the right underwater putty or epoxy, and we do that during the visit when it makes sense. A skimmer body that is cracked, a throat that keeps opening back up, or a deck that has moved a lot calls for a new skimmer. That means cutting out the deck around it, setting a new skimmer, re-plumbing it, and patching the deck, like the job in the photos here.

Skimmer lines

The pipe under the skimmer can leak too, especially where it joins the skimmer body. We pressure test each skimmer line from the skimmer to the equipment, so you know whether the leak is in the skimmer, the line or both.

Repair options

  • Seal the joint. When the leak is a gap at the throat and easy to reach, we seal it. Simple stops like this are included with the leak detection at no extra cost.
  • Repair the line. If the pipe under the skimmer leaks, we open the deck in one spot and fix it.
  • Replace the skimmer. When the body is cracked, we cut the deck, set a new skimmer, test it and patch the deck.
Finished skimmer replacement with the deck patched around the new lid
Finished: new skimmer in, deck patched.

Any repair beyond a simple stop is priced before work starts, with a warranty set for your project. Book a leak detection to find out which one you need.

Questions

How much does it cost to fix a pool skimmer leak?

A small gap at the throat is often sealed on the spot as part of the leak detection. A cracked skimmer that needs replacing is priced after we see it, before any work starts.

Can I seal a skimmer leak myself?

A small gap can be patched with an underwater putty, but it often fails if the real leak is in the pipe below. Test first, so you fix the right thing.

Why does my pool stop losing water below the skimmer?

If the leak is in the skimmer itself or at the seam with the shell, the water stops leaking once it drops below that point. It is one of the clearest clues there is.

How long does a skimmer replacement take?

The work itself usually takes a day, then the new concrete needs time to cure before the area is used normally. We give you the timeline with the estimate.

Keep reading

All articles

Book nowTextCall